Search:

Type: Posts; User: andre

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: C42 Wind screen

    by andre
    Replies
    3
    Views
    1,742

    Thanks for the advice guys, slow and gentle seems...

    Thanks for the advice guys, slow and gentle seems the best approach.

    André
  2. Thread: C42 Wind screen

    by andre
    Replies
    3
    Views
    1,742

    C42 Wind screen

    Hi, I need to remove the wind screen hoop tube on a c42, my main concern is how best to remove the pop rivets without damaging the screen . I believe the rivets are soft aluminium and would need...
  3. Thread: GAR form

    by andre
    Replies
    0
    Views
    238

    GAR form

    Hi, Any one know how far in advance the GAR Border force form can be submitted , I think it has to be at least four hours before arrival into the UK but can it be submitted a few days before.
    ...
  4. Replies
    26
    Views
    1,228

    Skydrive & Rotax to part company?

    I Sent this email to Rotax-

    José Boisjoli, Will you let us down . Bad press, see -http://forums.bmaa.org/default.aspx?f=15&m=135850 A Ciantar. ( This Forum's post about Skydrive & Rotax )

    And...
  5. Replies
    5
    Views
    362

    C42 Engine mount replacement

    Hi colin, it would cost more to replace the damaged part and you could not be sure of the integrity of the bits being reused. May as we'll get a complete new unit, I was thinking of not taking out...
  6. Replies
    5
    Views
    362

    C42 Engine mount replacement

    Hi terry, Crack on top left hand rear mount flange near the rubber mount bolt hole. Checked another c42 in our hanger & it too had the same thing . Red air say it can't be repaired. I believe ...
  7. Replies
    5
    Views
    362

    C42 Engine mount replacement

    Any information welcomed on what's involved in replacing the engine mount frame (Rotax 912) on a C42. I have not had a chance to have a look at the aircraft but from the build manual it looks like...
  8. Thread: Airzone to GA

    by andre
    Replies
    0
    Views
    195

    Airzone to GA

    Is it possible to adapt Airzone headsets to work on a Microavionics /GA
    intercom set up ? I found a few past posts on this, but with no definite outcome.

    Andre'
  9. Replies
    23
    Views
    939

    ac fuel pump on 912 engine

    made in china by any chance ?
  10. Replies
    9
    Views
    995

    S6 Rudder question

    HI Tim,
    If yours is a tail-wheel , as Bill said, it's to help balance & tension the rudder cables. If the bungee on a tail-wheel were removed or broke , would the pedals drop back & release the...
  11. Replies
    9
    Views
    995

    S6 Rudder question

    Hi Bill,
    got a reply on microlight forum which Leeds me to think that the bungee set up is only for tail braggers. although the book shows it for all types .
    Perhaps I should leave well...
  12. Replies
    9
    Views
    995

    S6 Rudder question

    Hi Phil,
    Nose wheel, I had a look at the build Manuel but can't see any info on nose wheel stops , I'll have a look on the Rans tomorrow, perhaps these have been bent , giving...
  13. Replies
    9
    Views
    995

    S6 Rudder question

    Looking through the build manual for my S6-ES I noticed that it shows a
    bungee chord fixed between the firewall and the rudder pedals. The
    manual says " This is used to help center the rudder in...
  14. Replies
    11
    Views
    626

    Cheapest (and decent) insurance?

    Dave, you should be able to get third party With passenger cover for under £250 & fully comp for about £500.00 (for £12,000 cover on your machine)if your machine is worth more than the premium will...
  15. Thread: S6 cable brakes

    by andre
    Replies
    23
    Views
    1,600

    S6 cable brakes

    Dan,
    My brakes where crap, check that the hubs are centered OK. one of my hubs was not centered with the back plate. a bit of cutting & welding to the leg bracket sorted this , also the cams...
  16. Replies
    22
    Views
    833

    Can you tn a trikes wing into a hang glider?

    wasn't the flash 2 wing also known as the widow maker.

    Andre'
  17. Replies
    5
    Views
    643

    Any problems getting insurance on a Rans?

    I got my insurance with Joint Aviation services, It covered me for my conversion from flex wing, My Rans has a 582 & has no problem climbing two up, solo I don't have to use full rpm. I have flown...
  18. Thread: SPAMFIELD '12

    by andre
    Replies
    165
    Views
    4,143

    SPAMFIELD '12

    Is there an up date to the list of who is attending. Tried to registered a few weeks ago , not sure if it worked , current list is dated November. Andre' emoticons/smile.gif
  19. Thread: 3 blad prop

    by andre
    Replies
    14
    Views
    1,206

    3 blad prop

    Nice one Bill. Happy new year . Andre'
  20. Replies
    8
    Views
    340

    what liscence ? & how to change it ??

    I agree Mike. The old PPL (M) is hardly mentioned in all the new license information that's going about. As you say, it is still valid & if you intend to only fly microlights its less hassle & less...
  21. Thread: Cable trim.

    by andre
    Replies
    3
    Views
    601

    Cable trim.

    Cable trim now installed on my S6ES & all paperwork completed. what a huge difference, not having to keep back pressure on the stick allows me more time & hands to sort out the map,radio, GPS & take...
  22. Replies
    3
    Views
    236

    Your chance to complain :-)

    yes the link work , but for those of as not in the know, how about some guidance, who is this for & do we all need to take action????.
  23. Replies
    4
    Views
    303

    prop' torque settings

    oops ! , correction inch pounds.

    thanks
  24. Replies
    4
    Views
    303

    prop' torque settings

    Thanks Nick,

    Looks like 20n/m or 175ft/lb for 8mm bolts.

    Andre'
  25. Replies
    4
    Views
    303

    prop' torque settings

    [hr]

    can any one tell me what is the torque setting for the propeller
    flange bolts for a 2 blade Warp drive prop' , rotax 582 engine.
Results 1 to 25 of 85
Page 1 of 4 1 2 3 4